6211-2RS/C3 Wheel Bearing For MAN
The DUHUI Bearing 6211-2RS/C3 is a single-row deep groove ball bearing with a 55 mm bore, 100 mm outer diameter, and 21 mm width. This sealed bearing features contact seals on both sides and C3 radial internal clearance for higher-temperature operating conditions, and is designed for MAN and Scania commercial vehicle applications requiring low friction and high-speed capability. It matches MAN OE specifications 06.31420.0302 and 85.90001.3024, with cross-references to SKF VKT 8707, Fersa 6211 2RS/C3, and Timken 6211C3.
Technical Specifications
| Specification | Value / Detail |
|---|---|
| DH Code | DWB3509 |
| Part Number | 6211-2RS/C3 |
| Product Type | Deep Groove Ball Bearing – Sealed, Single Row |
| Bore Diameter (d) | 55.00 mm (2.165 inch) |
| Outer Diameter (D) | 100.00 mm (3.937 inch) |
| Width (B) | 21.00 mm (0.827 inch) |
| Enclosure | 2RS – Rubber Seals on Both Sides |
| Radial Internal Clearance | C3 (Greater than Normal) |
| Material | High Carbon Chrome Steel (GCr15) |
| Weight | 0.58 kg (1.27 lb) |
Note: Dimensional data is based on SKF and Fersa published specifications for the 6211-2RS/C3 series. Please verify measurements against your original bearing before ordering.
Important: All information on this page is for reference only. Please verify OE numbers, dimensions, and vehicle fitment against your original part before ordering. Contact us for fitment confirmation.
DH Code & OE Numbers & Reference Numbers
DH Code: DWB3509
OE Numbers:
06.31420.0302, 85.90001.3024, 0 214 365, 1 360 882, 214 365
Reference Numbers (Interchange):
SKF: VKT 8707, VKT 8927
Fersa: 6211 2RS/C3, 6211-C3
Timken: 6211C3
FEBI BILSTEIN: 172412
DT Spare Parts: 1.16464
STELLOX: 83-25934-SX
Vehicle Fitment
MAN F2000: 26.273 DFC, 26.273 DFLC 1994-1995
Please verify OE number, dimensions and vehicle configuration before ordering.
Product Features
- Deep groove ball design accommodates radial loads and moderate axial loads in both directions – suitable for commercial vehicle applications.
- 2RS contact seals on both sides provide effective contamination protection – retains lubricant and excludes dirt and moisture.
- C3 radial internal clearance accommodates thermal expansion in higher-temperature operating conditions and high-speed applications.
- Metric configuration with 55 mm bore and 100 mm outer diameter matches MAN OE 06.31420.0302 and SKF VKT 8707 for direct replacement.
- Heat-treated GCr15 bearing steel with precision-ground raceways – low friction coefficient and high limiting speed.
- Factory pre-lubricated – no additional greasing required before installation.
Installation Notes
- Confirm bore diameter (55.00 mm) and outer diameter (100.00 mm) match your housing and shaft before installation.
- This is a sealed bearing – do not wash or re-lubricate before installation as the factory-fill grease is pre-installed.
- C3 clearance bearings are designed for higher-temperature applications – verify suitability with your operating conditions.
- Inspect the shaft and housing for wear or damage – replace if scoring or pitting is present.
- Press the bearing squarely into the housing or onto the shaft – never apply force directly through the rolling elements.
- Torque all fasteners to MAN or Scania service manual specifications.
About DUHUI Bearing
Manufactured by DUHUI Bearing – an automotive bearing supplier established in Zhejiang, China, in 2003. DUHUI produces deep groove ball bearings and automotive components to OE specifications. Contact us
